Remove SIM-lock patch generator

[arcade]

w200 error not unlock

[yurais]

Simox, thanks for the link, anas sorry to be late, but I did not receive notify by email for replies of the thread.

that tutorial doesnt replies all of my questions.

please read my quoted post again and try to reply ifd possible, I'm not that newbie, so, dont reply as if I was one ;), just that there are doubts :)

I suggest you to read the following tutorial before you try to do anything How to apply patches with SETool2 Lite V1.11. And don't forget to backup your GDFS(it is very important to have a backup, otherwise you can brick your phone forever.)
You can upgrade the CID with XS++ v3.x versions. When you connect the phone to XS++ it will ask you if you want to upgrade the CID or not. Yes, after your EROM CID will be 52 you can apply the patch...

Shitblast: The generated patch is good, I know for sure because that patch was tested on sen-se forum under v2.1 development. First reflash your MAIN firmware, then read this thread How to apply patches with SETool2 Lite V1.11, and follow the instruntions. Is should work. If not try jdflasher. Just read above a few posts and you will find the link for jdflasher...

xulos: I'm working on your problem...

[simox]

Simox, thanks for the link, anas sorry to be late, but I did not receive notify by email for replies of the thread.

that tutorial doesnt replies all of my questions.

please read my quoted post again and try to reply ifd possible, I'm not that newbie, so, dont reply as if I was one ;), just that there are doubts :)

I see, that post doesn't have much sense, sorry...
First upgrade the CID with XS++. It will ask you if you want to upgrade the CID, so press yes. Now you need a CID52 MAIN firmware to generate an unlock patch. Then follow that tutorial to apply the generated patch.

[jacko_oafc]

does any body have the firmware for a w850i RJ1C002 ??
thanks for any help

[haffonso]

Didn´t work with w580i.. Anyone had it working with w580i ? I need to unlock to use another SIM from other OP.

[del12]

it is locked to voda i guess now as when i put in orand or o2 it said inactive sim

please help me simox
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170801726461 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170801726461 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
INT LDRB2020_PRELOADER_FOR_SETOOL2
LDRB2020 LOADER FOR SETOOL2
Flash ID check:897E
Flash props sent ok
writing C:\Documents and Settings\Del\My Documents\mobile phone unlocking tools firmwear\unlocking sony k800i\K800_R1JC002_MAIN_VODAFONE_WI_RED52.mbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:9200
Will flash 460 blocks...
SSW loading returns:0
Going to execute VKP script....
Starting to process VKP patch script: C:\Documents and Settings\Del\My Documents\mobile phone unlocking tools firmwear\unlocking sony k800i\Remove_SIM_lock_K800_R1JC002.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44740000
Blocks selected OK. Reading blocks: 1
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
VKP script executed OK
Elapsed:596 secs.

anyone about to help me please
thankyou del

[CL6]

This patch does work.

However it has to accompany with SETool2 and XS++ to make your phone unlock, at least it worked on my K610i locked by UK 3.

In order to generate the correct patch, you will have to find the right MAIN firmware. To me, this could be the most difficult part since I decided not to spend a penny to get the phone unlock.

[pakkiz]

what about DB2010 ? does it work on those phones?

[onlyone]

yes it does IF the phone is db2010 CID49

[Mocko]

I just unlocked Z610i. Updated to CID52 with XS++, then applied patch with SETool2 Lite v1.11.

I've flashed the phone with R6DA001:
Z610_R6DA001_MAIN_GENERIC_MY_RED52.mbn

but for FS I found just Z610_R6DA001_FS_C_ASIA_RED52.fbn , so after customizing, I've english only...

So I'm looking for:

Z610_R1KH001_FS_EUROPE_2_RED52.fbn
or
Z610_R6DA001_FS_EUROPE_2_RED52.fbn


P.S. I'm unable to unlock W200i (CID52). At the end, it says:

Starting to process VKP patch script: \\Pc1\pc1-mis documentos\SIMLockPachGen1.1\vkp\Remove_SIM_lock_W 200_R4GB001.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44CC0000
Blocks selected OK. Reading blocks: 1
Block @ $44CC0000 read error. Have only: 00000000 bytes
Elapsed:8 secs."???

With XS++ I can't flash/customize this phone, so I've tried to do everything with setool2 Lite...
Any suggestions?