W580 - Dead ? There's a hope ?!

Helo, people.. I flash my w580i , but the flash with patch and elf structure inside don't work on my cel, with the same firmware (R8BE001), so I decide to re-flash with a firmware that I knew that work ,so I did, but when finish the process, (using Setool 1.11) the cell phone don't turn on and a red light blink, ok !
After that i seach on google, another foruns , some way to start all over again, in this moment my cell still boot using the C, so I check my gdfs backup , separate a correct main and fs to flash, but the cell phoen won't to boot using C, only 2+5 keys.

I try to rechage the battery, suspecting of low battery , but with the cell that way, the battery don't charge after 4 hours plugged on AC , I take my friend w580i and use his cell to recharge my battery, but still not working, the cell and other way to boot, now i ask for you my friends, theres a way to recovery my cell phoen without to send to sony ericsson assistence ?!? I think to use setool 2 or any other paid software, but i don't have sure if this could help.

Follow my logs of setool.

-> Trying to reflash with main,fs e TPA

FILE RECOGNIZED AS CUSTOMIZATION PACKAGE.
CDA:CDA102568/16
MODEL:HB1-06 Gen
VARIANT:AMERICA_2
LANGUAGE: EN
LANGUAGE: PB
LANGUAGE: XL
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35598902288117 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:51 PAF:1 IMEI:35598902288117 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
Elapsed:1496 secs.



-> Trying to wirte a EROM
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35598902288117 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:2 secs.

- Trying to recovery GDFS from a previous backup

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35598902288117 CERT:N/A
FLASH CID:52 COLOR:RED
Abort all operations.
no ack during gdfs_readvar !
Can't read SCRC unit
Elapsed:111 secs.
file can't be found or opened
Elapsed:0 secs.



- Another log , another erro, I don't remember the reason of this error:

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35598902288117 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
wrong response, break.
loader fs startup failed, that is fatal
Elapsed:203 secs.


:(


Thanks for while !

REPAIRING EROM GUIDES for most sonyericsson phones

A sign of a dead erom is normally a blinking red led in the infra red port.

Have a nice day

Or you can try with this steps plz help... k810 is dead what can i do ? - Top Sony Forums ,before you try to repair EROM - maybe he isn't damaged.
But if that don't work - do like @jasmin told you

Thanks friends, but I have some doubts:



Senter said:

Must use Setool.

1. Reinsert battery and do NOT turn on phone!
2. Start Setool and click Identify
3. Hold 2 and 5 together and in the meantime put the USB cable.
When hear that sound (though that connects USB flash memory) disconnect USB cable, reinsert battery and do NOT turn on phone!
4. Start XS++ v3.1 and click Connect.
5. Hold "C" button in the meantime put the USB cable.
6. Flash only Main, then again disconnect USB cable, reinsert battery and now can turn on phone - work fine as before.

Trying to do this:

1. Reinsert battery and do NOT turn on phone!
-> Ok
2. Start Setool and click Identify
-> Ok
3. Hold 2 and 5 together and in the meantime put the USB cable.
When hear that sound (though that connects USB flash memory) disconnect USB cable, reinsert battery and do NOT turn on phone!
-> Reinsert the battery ? But is still there, wich is the righ momento to pull off the battery ??? I missed ! I try to do without remove the battery, just the cable.
4. Start XS++ v3.1 and click Connect.
-> Ok
5. Hold "C" button in the meantime put the USB cable.
-> Ok
6. Flash only Main, then again disconnect USB cable, reinsert battery and now can turn on phone - work fine as before.
-> My XS++ don't detect the phone , just show a message: "Can't send 0x05 "


Thanks , my friends. !! I still have some hope, to make my cell workout !!

When you hear sound - that mean that Setool done his job (you will see in Setool at the end "Ealpsed ..sec) and you can unplag USB cable from phone,reinsert battery and follow thrue the end. If you don't remove battery - that procedure don't work

Quote:

---

Originally Posted by seamonkey

When you hear sound - that mean that Setool done his job (you will see in Setool at the end "Ealpsed ..sec) and you can unplag USB cable from phone,reinsert battery and follow thrue the end. If you don't remove battery - that procedure don't work

---

Ok, but when I take off the battery, adn reinsert in the phone to boot with "C" pressed, the XS++ don't detect the phone and the windows default sound of detected don't play !!!


More information, that time, I'm not waiting the setool finish, so I finish and the log is:

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:XXXXXXXXXX CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can't read SCRC unit
Elapsed:79 secs.

Now your battery is empty and you can't charge with phone (but try,maybe it will),so try to borrow another one from friend

Seamonkey ok ! I 'll try.

but please, check my sequence:

- Cell w/o battery and disconnected
- Put the battery
- Press 2 + 5 keys
- Plug USB cable , wait Setool Detect !
- after the detect sound, open XS++
- unplug USB cable, and remove the battery
- put battery again, press C and plug USB
- click Connect

just it !? When I dont' remove the battery, I can't boot with C pressed, otherwise not !

Sorry to ask to you give me detailed explains !!
=)

goto sony ericson site download update service software from support install software and follow instructions you will have to use dcu60 cable usb that cam with the phone it will re install softare and phone will be back to normal this should work with most of sony ericsons i had gdf scrc problems after flash k800 it worked for me good luck

Thanks for the suggest, but I send the phone to the Sony Ericsson assistence. I tried the sony ericsson update service, but when the cel reboot , the updater can't detect him.
THe sony ericsson assistence, give me back my cell with another face plate and fixed, but the IMEI was changed, I think the SE put away the old damaged main board and put a new one on it, put the new frame and send me back... easy to fix when you have all the pieces =)

Thanks a Lot, and this post may be locked !