PDA

Ver la versión completa : [RESUELTO] w200 error al hacer desbloqueo


cellcarcol
28/05/2008, 16:15:07
tengo un w200 y cuando quiero abrirle las bandas me arroja este error




log
----


v0.914034/UNI
CARD SERIAL: 000*****
Loaded 51 flash descriptors

THAT ACTION IS ILLEGAL,IF YOU DOING IT
FOR ANY PURPOSE, OTHER THAN REPAIR PHONE

SIGNED MODE (USING SERVER).
ALTERNATIVE SECURITY BYPASS ENABLED.
ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED

PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35427001****** CERT:RED
LDR:061205 1354 HAN_DB2012_FLASHLOADER_R2B012_CXC1326738
Flash ID check:897E
Flash props sent ok
LDR:070410 1405 HANCXC1327364_COMPACT_SEMC_CS_LOADER_1_R3B009
loader startup: executed
loader GDFS startup: executed
loader filesystem startup: executed
loader unlock: executed
file block nak,err:3
Can't write file (executor.b)

DISCONNECT PHONE NOW
INSERT SIM CARD, FULLY TURN PHONE ON AND ATTACH AGAIN
BE SURE THAT YOU SET PHONE IN "PHONE MODE"
IF ASKED, INSTALL PHONE DRIVERS

SEARCHING FOR PHONE, "STOP" TO ABORT
PHONE FOUND AT COM10
PHONE READY TO PROCEED
CAN'T START EXECUTOR,RETRYING...
CAN'T START EXECUTOR,RETRYING...
CAN'T START EXECUTOR,RETRYING...
EXECUTOR STARTED

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED

PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
PROCEDURE WAS STOPPED BY USER
Elapsed: 127 secs.

-------------------------------------------------

Hago nuevamente el proceso, ya no me arroja ese error, pero cuando dice que espere 15 segundos de ahi no sigue.



v0.914034/UNI
CARD SERIAL: 000*****
Loaded 51 flash descriptors

THAT ACTION IS ILLEGAL,IF YOU DOING IT
FOR ANY PURPOSE, OTHER THAN REPAIR PHONE

SIGNED MODE (USING SERVER).
ALTERNATIVE SECURITY BYPASS ENABLED.
ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED

PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35427001****** CERT:RED
LDR:061205 1354 HAN_DB2012_FLASHLOADER_R2B012_CXC1326738
Flash ID check:897E
Flash props sent ok
LDR:070410 1405 HANCXC1327364_COMPACT_SEMC_CS_LOADER_1_R3B009
loader startup: executed
loader GDFS startup: executed
loader filesystem startup: executed
loader unlock: executed

DISCONNECT PHONE NOW
INSERT SIM CARD, FULLY TURN PHONE ON AND ATTACH AGAIN
BE SURE THAT YOU SET PHONE IN "PHONE MODE"
IF ASKED, INSTALL PHONE DRIVERS

SEARCHING FOR PHONE, "STOP" TO ABORT
PHONE FOUND AT COM10
PHONE READY TO PROCEED
EXECUTOR STARTED

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED

PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...



Estos son mis dos casos con el mismo telefono w200.

espero pronta ayuda.
Ivan08v
28/05/2008, 16:24:49
Chequea que los telefonos tengan memoria interna disponible para escribir el executor...
Que hace el telefono cuando te aparece el error de "loader not responds"?Se enciende...Si asi es cuando se prenda anda a Juegos y ejecuta el archivo Executor...Luego conectas el telefono y seguis con el proceso...
ts002
28/05/2008, 16:38:56
habilita: SIGNED MODE (USING SERVER),ENABLE ALTERNATIVE SECURITY BYPASS y ENABLE PRELOADER SECURITY BYPASS.

Saludos!!
Ivan08v
28/05/2008, 16:45:25
habilita: SIGNED MODE (USING SERVER),ENABLE ALTERNATIVE SECURITY BYPASS y ENABLE PRELOADER SECURITY BYPASS.

----------------------------------------------------
SIGNED MODE (USING SERVER).
ALTERNATIVE SECURITY BYPASS ENABLED.
ChipID:8040,EMP protocol:0301
NEW SECURITY MODEL DETECTED

PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
----------------------------------------------------

Amigo Hatred en el log podemos ver las opciones marcadas y el CID del telefono...
El Preloader seria en caso de que fuera CID50/51....:)

Suerte
cellcarcol
28/05/2008, 17:10:22
el era cid 51 y lo subi a cid 52, ya habia realizado otros y nunca me habia sucedio esto.
69eyes
28/05/2008, 17:18:32
Claro, pero ya intentaste con la solución que te dio ivan?
Sigue probando y postea resultados.
cellcarcol
28/05/2008, 18:11:52
la solucion fue sencilla, ejecute el excutor y el telefono se apago, despues active la casilla unlock y la casilla enable preloader securit bipass.


y me prendio bien y desbloqueado.