XS++ 3.1 Guide-Flashing, Customizing, Recovering

[riders4sia]

i'm from india too, thought i have already given, anyway here are the files you need
MAIN : W810_R4EK001_MAIN_GENERIC_HN_RED49
FS : W810_R4EK001_FS_AMERICA_2_RED49
custpack : W810_CDA102555_107_R2A_Generic_AMERICA_2
you can use if you ought to upgrade, it's the only upgrade for CID49 but if you like stick it with the current version, use these
MAIN : W810_R4EA031_MAIN_GENERIC_HN_RED49
FS : W810_R4ED001_FS_S_ASIA_LEVAN_RED49
custpack : W810_CDA102555_110_R2A_Generic_S_ASIA_LEVAN

[megaxx]

Hello there. Im using w300i. where do i get the firmware to browse it, at step 3.2?

[riders4sia]

look at the top of this page, you'll find downloads

[megaxx]

Sorry for double post, but help me please :(
I can't find the cda and and region that i need. I have many there but not mine. I see it on the list that was posted on the thread, but on on xs++ :(

[kreacher]

My K790i suddenly turned off and was not turning on. When I tried to start the phone it came up to the start animation then the screen kept blinking white/ black. I tried SE update service but since I had latest firmware it did not flash the phone.
Finally I used XS++ 3.1 (BTW big thanks for the software and this guide) to flash the latest firmware again. The phone started working but now after a few weeks it has again turned off and is not starting.
What could be the problem with the phone?

[sonnyboy]

used xs++ on two k800i one for screen of death and yesterday for a k800i which would not ring anymore. Upgraded the last one from red 49 to red 52 and then flashed on both occasions worked great.
thanks for your help.

[notisjunio]

thnksssssssss

[burgers]

After performing a (K610_R1GB001_FS_EUROPE_5_RED51) flash using XS++
And a interruption from a power failure right at the worst time.
I read the Guideline from mohdumer...
It would seem that there is no recovery from a "bad" main/file system firmware flash

All I get is this response now...

08:08:21| XS++ v3.2 Dev1 (Crystal) Ready !08:08:21| Executed on Microsoft Windows XP08:08:55| 08:08:55| Attempting to open the interface...08:08:55| 08:08:55| TURN OFF PHONE!08:08:55| Hold 'C' button on phone and connect phone NOW.08:08:55| You have 30 seconds...08:08:55| 08:09:26| Error: Cannot open phone communication port08:09:28| Disconnected... Unplug the phone08:59:50| XS++ v3.2 Dev1 (Crystal) Ready !

08:59:50| Executed on Microsoft Windows XP
09:00:06| Attempting to open the interface...

09:00:06| TURN OFF PHONE!
09:00:06| Hold 'C' button on phone and connect phone NOW.
09:00:06| You have 30 seconds...

09:00:37| Error: Cannot open phone communication port
09:00:39| Disconnected... Unplug the phone
09:01:13| Shutting down...

In UR Opinion is there any hope or RIP?
Appreciated reply

[mentheleng]

Try to check your cable first. If that ok, you can try to take out your batteray for at least minutes, before you insert again. Sometimes (a lot at mine), works perfectly. It cause by uncompleted flash for instance. Hope it help.

[burgers]

Note to anyone having problems with a dead phone Refer to (and I mean totally dead. No response or blinking light)
Refer to Senter adviceThread "Totally dead K800i"

Top Sony Forums - View Profile: senter

I had a brick and this advice returned my K610i back to the living
You must have latest Setool lite and XS++ installed.