Remove SIM-lock patch generator

[simox]

K800i

Flashed main with XS++ ok
Flashed FS with XS++ ok
Flashed Cust with XS++ ok
cannot get unlock patch icon to work, phone still locked

Flashed main with SeTool2lt ok
Flashed FS with SeTool2lt FAIL

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
INT LDR:DB2020_PRELOADER_FOR_SETOOL2
LDR:DB2020 LOADER FOR SETOOL2
Flash ID check:897E
Flash props sent ok
CSloader version:
DB2020_FILESYSTEMLOADER_FOR_SETOOL2
loader startup: executed
wrong response, break.
loader fs startup failed, that is fatal
Elapsed:583 secs.

What is going wrong??
I loaded the USB drivers

Just trying to unlock phone

I think you made something wrong. Follow this tutorial: How to apply patches with SETool2 Lite V1.11

seunlock:

hello if i unlock my phone in this way and make a backup and flash it to another phone does that phone be unlocked?

Yes, that phone will be unlocked, but be careful: backup the MAIN firmware only. If you backup the GDFS too, you can brick the another phone.

bennyboy™ and Shitblast:
I have searched a bit about "Inactive SIM" problem.
Try the following:
1.) Swich off the phone, remove the battery and SIM card. Put back the battery(do not put back the SIM card). Turn on the phone, and when it asks you to put a SIM card, swich off the phone and put back the SIM card. This operation is called soft reset.
2.)If it doesn't help reflash the phone with the latest firmware version(try an unbranded one) and try with original SIM card. If it works unlock the phone and try again.
If it doesn't works then can be two reasons: the SIM card is defect or your IMEI number is blacklisted(someone reported the phone as stolen).

[thecce]

Please, Simox, do you have any advice for unlock K310i CID 50?

[simox]

Please, Simox, do you have any advice for unlock K310i CID 50?

DB2012 CID50 phones cannot be unlocked for free. Sorry...
However you can unlock with paid services. You can try SekingServer for example.

[thecce]

Thanks a lot man, I'll go to a service :)
Good luck and have a nice life!

[joca]

[QUOTE=simox;64693]I think you made something wrong. Follow this tutorial: How to apply patches with SETool2 Lite V1.11 [QUOTE=simox;64693]

I've followed it several times, all failed at some stage.
I am going to give up. :o
It is beating my brains out :eek:

[simox]

I think you made something wrong. Follow this tutorial: How to apply patches with SETool2 Lite V1.11

I've followed it several times, all failed at some stage.
I am going to give up. :o
It is beating my brains out :eek:

Don't give up;)
First flash your phone (MAIN, FS, cust pack) with XS++. Do not flash it with SETool2 lite, just patch it following that tutorial. Should work...

[joca]

Had just finished flashing phone with XS++.
Done all as per guide. Phone still is locked (EXTENDED LOCK)

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601933121 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601933121 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
INT LDR:DB2020_PRELOADER_FOR_SETOOL2
LDR:DB2020 LOADER FOR SETOOL2
Flash ID check:897E
Flash props sent ok
writing C:\Documents and Settings\Boss\Desktop\K800_R8BA024_MAIN_GENERIC_WI _RED52.mbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:9200
Will flash 460 blocks...
SSW loading returns:0
Going to execute VKP script....
Starting to process VKP patch script: C:\Documents and Settings\Boss\Desktop\SETool\qamaker\quick_access_ K800_R8BA024.vkp
VKP script loaded OK. Lines: 1637
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44140000
New block #0001 added: $45C80000
Blocks selected OK. Reading blocks: 2
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
Block 1 written
VKP script executed OK
Elapsed:766 secs.

:( :( :( :(