Remove SIM-lock patch generator

[Lunchbox]

THANKYOU SO SO MUCH!! I tried to rebrand my v630 to a k610 using wotan, and it relocked it to Vodaphone! Thanks to your guide and code its now unlocked again, admittedly as a w660 cos i couldn't find any k610 firmware. Thanks a million!!

[yurais]

Simox

Are you working on making patches for new A2 phones?

THe iother day, by mistake, I tried to gennerate a patch for a W910 Firmware, and the software didnt work.
I didnt know the W910 was A2, so I just tried, then I read it is a new platform, even if you release a version supporting this platform, do you think there could be a chance to patch it ?

mmaybe Xs++3.2 ?
regards

Yurais

[simox]

davidw89:
Sorry for late reply, but I missed your post.
What error message you get? Please post an identify log as well.

newguyoz:
You need to install the USB Flash driver: USB Flash Driver Installation - Guide.
Firsrt turn off the phone, remove the battery, wait a few minutes, then insert it back. Now click the button on program(e.g. FLASH, Write Script etc.) press and HOLD the C key on phone, and connect the cable. When you see some progress in program, release the C key.

yurais:
I'm not plannig to do that until we can patch A2 phones...

[turca]

No work, I test in cid51

[simox]

Upgrade the EROM CID to 52 using XS++ and it will work.

[simox]

You haven't followed the guide, and now you wonder what happened???
The answer: Your phone is dead of course.
You can revive it if you reflash the MAIN firmware. Then unlock your phone by following CAREFULLY the guide, and do not skip any step because there isn't any pointless step.

[yurais]

I must admit that am sorry...

I thought the quickaccess stuff was only for making life easier later for patching more stuff, so I thought I could just use the bypass mmethof, since I only need to patch this phone once for sure.

Can I use the bypass method with the MAIN firmware and only patch the phone.
I Mean, is there ANY way to apply the patch WITHOUT using the QuickAccess story ?

Yurais

[simox]

You can skip the quick access part, if you don't want to apply other patches in the future, otherwise I don't recommend it.
If you want to skip the quick access:
start with step II. then follow the step I. Here, instead of quick access put the "unlock" patch generated by my tool. Everything else remain unchanged(but you no need to make the quick access patch of course).

[yurais]

You can skip the quick access part, if you don't want to apply other patches in the future, otherwise I don't recommend it.
If you want to skip the quick access:
start with step II. then follow the step I. Here, instead of quick access put the "unlock" patch generated by my tool. Everything else remain unchanged(but you no need to make the quick access patch of course).

and can I patch the generated VKP for unlock, avoding the quick access, and also without having teh MAIN file ?

Actually I believe that what screwed the phone was an Incorrect Patch, becase as I said, setool2lite warned of Differences on the patch against the FIrmware andn applied it anyways, this, MUST be what sucked the phone so hard.

Simox thanks for your replies, but I think this conversation will serve to many guys, I used to unlock db2020 with seking, I have been forced to mmove to the free stuff because I am having problems with paypal right now, and can not make payment, so, forced to use the free zone ;), thats why I am a newbie on the patching story

[yurais]

Ok, because I had a different version on the phone than the version I could find at iprotebe.cz, this what I did to Unbrick the phone:

(Used Service Cable)
Generated the quick_access Patch with qamaker.
Added both Main and FS to the list, ticked the Bypass checkbox, added the quick_access_patch generated by qa_maker on the Misc textbox, and clicked FLASH
had to wait about half an hour.
All done
Added the Unlock vkp , ticked Use QUick Access Patch, cleared both MAIN and FS from the list, unticked B?ypass db2020 ..., clicked Write Script.
This did NOT work at all using the Service Cable, I had to use the DCU11 Cable (USB Cable) for the write script using quick_access memthod to work.

After all that, because of configuration problem, just openes Xs++ and Finalized the phone.

WalkMan is now back to life.

But I still do have the same question: How can I patch_unlock, WITHOUT using the quick_access stuff, no matter how long it takes.

I think that If I add MAIN, add unlock_vkp_script, tick Bypass DB2020... and click on FLASH it Should Work, SIMOX ??