Remove SIM-lock patch generator

[SeaMonkey]

first off: thanks a lot simox for the quick response.
everything went well until the last step. as you write "3. Tick Use "quick access" patch checkbox" - my set v1.10 doesn't seem to have that checkbox? or are you talking about "quick_access_XYYY_R8BA024.vkp" (which i dl'ed somewhere!?)?

i am receiving this status:

Starting to process VKP patch script: G:\SIMLockPatchGen\vkp\Remove_SIM_lock_W880_R8BA02 4.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44740000
Blocks selected OK. Reading blocks: 1
Block @ $44740000 read error. Have only: 00000000 bytes
Elapsed:9 secs.

First of all find v.1.11 and than try again (thats last version for now)

[danbwoi]

omg, and i have always seen myself as a not-dumb-user, thanks anyways seamonkey. anyone who wants to slap me, pm me.

___________________

STILL it doesn't work. it's failing while trying to launch the embedded bootloader -> embedded flashloader not responds!

[SeaMonkey]

omg, and i have always seen myself as a not-dumb-user, thanks anyways seamonkey. anyone who wants to slap me, pm me.

___________________

STILL it doesn't work. it's failing while trying to launch the embedded bootloader -> embedded flashloader not responds!

Just try to connect with XS++3.1 and if XS recognized and read your phone post log here without IMEI

[danbwoi]

22:25:46| Baseband ID: 9900
22:25:46| Protocol Version: 3.1
22:25:47| Phone name detected!
22:25:47|
22:25:47| Profiling SEMC phone...
22:25:47| Platform: DB2020
22:25:47| OTP CID: 51
22:25:47| EROM CID: 52
22:25:47| EROM Color: Red
22:25:47| IMEI: xxxxxxxxxxxxx
22:25:47| Phone ID: W880
22:25:47| Region: VFE_LIVE_2
22:25:47| CDA: CDA102719/75 R5A
22:25:47| Firmware Version: R1JC002
22:25:47| EROM: R3A016
22:25:47| Ready for operation!

[simox]

the phone gets recognized as database and is booting and the display showing the usb-instructions. what do i need to do?

It is probably a driver problem. First reinstall the USB Flash Driver what comes with SETool2 Lite v1.11(it is important to use that driver). If the problem persists, then clean the phone's port, and the cable connectors. Also you can try other USB ports on your PC (without any hub).

[danbwoi]

Hrmpf, it does not work. I have tried all my USB Ports, the Cables are factory brand new. I am close to despair..:(:confused:
I will delete ggsemc.sys and ggflt.sys and try whether the automatic recognition works. still, i've tried it with the automatic mode but it wouldn't recognize the drivers.

damn i was so close :rolleyes:

_____
Don't get me wrong, I've read the usb flash installation guide..

Whatever I do, it makes no difference. Is there a Possibility to delete the Phone as Device from my PC System, causing the PC to recognize it as a new device and having to read and install the USB Flash Drivers from SETool aside from simply deleting the both files mentioned above?
I am asking because this is the onliest way of solving this issue i can figure out right now.

[simox]

Follow the USB Flash Drive installation guide using the driver what comes with SETool2 Lite v1.11. The driver path is [SETool2 Lite v1.11]\drivers\USBFlash_driver\

[danbwoi]

Windows is persisting in use of the M$ driver (usbstor.sys) although i have performed the steps in the tutorial correctly. I have tried it on a different PC, and it didn't work either. I am sure that I have the correct files (r1jc002), the flashing went well, the branding is gone. It is simply all about the Patch..i don't know what I am doing wrong :(

[simox]

Then try jdflasher to apply the patches instead of SETool2 Lite.

[Skyaxe]

Can you do a tutorial on removing DB2000 CID49 please or is it the same process as the DB2010 and DB2020 tutorials.

Cheers

Skyaxe