"Error: Phone not power up" Please help, tried everything.

[zeriuz]

Hi everyone!
First i just want to say that ive read every thread about this problem on internet ;P but i havent found an answer. Hoping that someone here could explain this to me.

Ok, to the problem. I have an SE T630 wich i want to unlock. Ive bought a T28 cable and the site says that it "can be used with most unlocking program on the internet".

1. I have the computer off and the cable/phone connected.
2. Starting up the computer and the phone starts charching (although ive already charged it to 100%)
3. Then the phone turns off and starts up again and keeps doing this all the time?
( 4. I have suceeded to connect to the phone through MOBILedit )
5. When im trying to unlock the phone with SEMCtool 2.2 / 3.3 it just says "phone not power up".
6. With "Div" i think its called? It just says "Bypass boot authority" but i think the software have skipped the connecting part.

Ive tried with/without battery and then connect the battery just before i press "do jobs". Im pressing the power-button on the phone like a freak but nothing happens. Ive also cleaned up the connector but with the same result.

So... i need somehow to connect to my phone!

//Jonathan

[TheRascal]

Hi everyone!
First i just want to say that ive read every thread about this problem on internet ;P but i havent found an answer. Hoping that someone here could explain this to me.

Ok, to the problem. I have an SE T630 wich i want to unlock. Ive bought a T28 cable and the site says that it "can be used with most unlocking program on the internet".

1. I have the computer off and the cable/phone connected.
2. Starting up the computer and the phone starts charching (although ive already charged it to 100%)
3. Then the phone turns off and starts up again and keeps doing this all the time?
( 4. I have suceeded to connect to the phone through MOBILedit )
5. When im trying to unlock the phone with SEMCtool 2.2 / 3.3 it just says "phone not power up".
6. With "Div" i think its called? It just says "Bypass boot authority" but i think the software have skipped the connecting part.

Ive tried with/without battery and then connect the battery just before i press "do jobs". Im pressing the power-button on the phone like a freak but nothing happens. Ive also cleaned up the connector but with the same result.

So... i need somehow to connect to my phone!

//Jonathan

U need to remove RSA and then to unlock your phone m8. Some FW have RSA protection that's why free tools can't unlock them until u remove the RSA.

[jagadeesh]

blindly charge ur phone batery and with proper firmwares in hand and flash ur mobile it will show life. it will take 5hrs to flash or even more.

[zeriuz]

U need to remove RSA and then to unlock your phone m8. Some FW have RSA protection that's why free tools can't unlock them until u remove the RSA.

1. okey, new edit.. I CANT CONNECT TO THE PHONE. have tried everything as you can read above but. dont know whats wrong! and as long as i cant connect to it i cant remove RSA or unlock the phone.

2. when im connecting the phone to the cable and i turn the computer on it starts charging.. always.. maybe 1/10 it doesnt starts charging

3. wich software should i be using to remove RSA? im using a t-28 cable and Div only supports terminator dongle..? and in semctool you cant remove it :P
(sorry about my english, but im trying : )

[onlyone]

i'll tell you what to do. the other told you creppy thing, nothing you can use.
so find the picture below, it's self explainatory:
you must unsold the red wire (5V) form the side of the cable that goes into the phone.
if your cable is a service cable already, you will notice that pin 6 and 7 are in use for rx/tx transmision. but if your cable is using pin 4 and 5 then you need to unslod 4 and move to 6 and also unslod 5 and move to 7. then shortcut pin 9 and 11 also, cut the red wire. the wire at pin 10 must stay in place.




now my friend you can use usbsmart 3.3 to read all codes from your phone.
take care

usbsmart 3.3 can be found here:
RapidShare: 1-Click Webhosting

PS the red wire is charging your phone and you will be unable to unlock if you don't unsold it or cut it because your phone will start over and over again (i wrote this so you know why the red wire must be cutted off)

[zeriuz]

i'll tell you what to do. the other told you creppy thing, nothing you can use.
so find the picture below, it's self explainatory:
you must unsold the red wire (5V) form the side of the cable that goes into the phone.
if your cable is a service cable already, you will notice that pin 6 and 7 are in use for rx/tx transmision. but if your cable is using pin 4 and 5 then you need to unslod 4 and move to 6 and also unslod 5 and move to 7. then shortcut pin 9 and 11 also, cut the red wire. the wire at pin 10 must stay in place.

thanks a lot : )
opened my cable, and found some resistors? what am i supposed to do with these? also, i dont have any red cable.? but im guessing that the yellow one is "your red". also, my green cable is attatched to pin 10 AND pin 2!? as you can see on the picture there's another resistor just before pin 2.



this is how it looks. so am i thinking right if i?:

1. change blue cable -> pin 6
2. change white -> pin 7
3. shortcut pin 9 - pin 11
4. cut of yellow cable

[onlyone]

yes you understand very well
remove any connection from pin 2 to 10 as you don't need that
also my red wire (in every cable the 5V wire or any wire that provides energy must be red) is yellow wire at your cable so cut it. also shortcut 9 and 11
pin 10 remain connected only to the light blue wire (but cut connection to pin2)
move the other 2 wires from 4 and 5 to 6 and 7
that shoul do the trick

PS your cable was not a service cable as stated by people who lold that to you. it's a data cable so of course it needs transition to service cable as mentioned above...
good luck.

[zeriuz]

yes you understand very well
remove any connection from pin 2 to 10 as you don't need that
also my red wire (in every cable the 5V wire or any wire that provides energy must be red) is yellow wire at your cable so cut it. also shortcut 9 and 11
pin 10 remain connected only to the light blue wire (but cut connection to pin2)
move the other 2 wires from 4 and 5 to 6 and 7
that shoul do the trick

PS your cable was not a service cable as stated by people who lold that to you. it's a data cable so of course it needs transition to service cable as mentioned above...
good luck.

ive fixed it :D
after an our in my garage i succeded to unlock my phone.
i switched place on white+blue, DIDN'T cut the yellow one at all, just made a shortcut between 9-11... and the "green = ground" is connected both to pin 10 and 2. i also kept the two resistors.

i didnt think that i would work but it did!

yeah, i saw in som conversion guide too that my cable was a "data cable".

im so happy! thanks a lot for your help! you're an angel (:

[Taurus3]

charge phone battery and flash with compatible firmware of main ,fs, customization found in top sony download area, that's it u can bring dead to live in top sony.