XS++ 2.x Guide

[djape48]

I tried to flash my w700i (originally R1DB001) with xs++, W700_R1CA021_MAIN_EU_1_CR_RED49 as main, W700_R1CA021_FS_EMEA_2_RED49 as FS, and customization w700 EMEA_2 and xs stuck at Activating filesystem. I stoped procedure after 30 minutes, and phone couldn't turn on in phone mode (configuration error...). When select music mode at startup (works normally) and enter service info/software info - it is r1ca021. How can I fix my phone? This is my first flashing, maybe I shouldn't do it :)

[darkfuture]

thank you i want to flash my k610i to w660
but how?

[ts013]

djape: Try using an older version (1.2 or 1.5)

[djape48]

Tried xs 1.5 but everytime stops here:

18:38:17| Ready for operation!
18:38:39| Starting Loader Unlock Hack...
18:38:39| ***** R3L
18:38:39| Cannot open CID36_00_R3L.bin
18:38:39| Wait for loader hello
18:38:54| ++ Error: Flashing failed
18:38:54| Disconnected... Unplug the phone
18:38:56| Shutting down...

Now I tried xs 3.0 beta and another failure:

19:03:06| Done uploading
19:03:06| Sending shutdown command to phone...
19:03:06| Customizing was SUCCESSFUL!
19:03:06|
19:03:06| Disconnect phone from USB-port and wait for
19:03:06| further instructions.
19:03:06| You have 10 seconds.
19:03:06|
19:03:16| Open the battery-cover and reinsert the battery.
19:03:16| Hold C Button on phone and connect phone again.
19:03:16| You have 30 seconds.
19:03:16|
19:03:23| Baseband ID: 8040
19:03:23| DB2010 Marita compact
19:03:23| Protocol Version: 3.1
19:03:23| Phone has restarted successfully...
19:03:23|
19:03:23| Sending db2010_cid49red_flash_r2b.bin...
19:03:23| Applet ID: 051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2B
19:03:23| This is a FLASH loader
19:03:23| Flashing breakinfirm\W700_R1CA021.bin
19:03:23| Header type: BABE
19:03:23| 2 flashblocks
19:03:23| Binary acknowledge failed with: 15
19:03:23| Failed
19:03:35| Error: Flashing failed
19:03:35| Disconnected... Unplug the phone
19:03:39| Shutting down...

Stupid w700

[ts013]

Please post up the log when you just connect the phone.
A log of the identifying process done with SE Tool lite would be nice too.

[djape48]

18:39:11| XS++ v3.0 beta (Sinyar) Ready !
18:39:11| Executed on Microsoft Windows XP
18:39:19|
18:39:19| Attempting to open the interface...
18:39:19|
18:39:19| TURN OFF PHONE!
18:39:19| Hold 'C' button on phone and connect phone NOW.
18:39:19| You have 30 seconds...
18:39:19|
18:39:25| Baseband ID: 8040
18:39:25| DB2010 Marita compact
18:39:25| Protocol Version: 3.1
18:39:25|
18:39:25| Sending db2010_cid00_prodid_p3l.bin...
18:39:26| Applet ID: 061113 1250 ALUCXC125872_COMPACTPRODUCTION_ID_LOADER P3
18:39:26| This is a PRODUCTION_ID loader
18:39:26| Activating GDFS...
18:39:26| Phone name detected!
18:39:26|
18:39:26| Profiling SEMC phone...
18:39:26| Baseband ID: DB2010
18:39:26| OTP CID: 49
18:39:26| EROM CID: 49
18:39:26| EROM Color: Red
18:39:26| IMEI: 35167301xxxxxx
18:39:26| Phone ID: W700
18:39:26| Network: EMEA_2
18:39:26| CDA: CDA102295/7 R2A
18:39:26| Firmware Version: R1CA021
18:39:26| EROM: n/a
18:39:26| Ready for operation!
18:39:36| ~~~~~~~~~~ Custpack information ~~~~~~~~~~
18:39:36| Custpack: APAC_1 (CDA102580/101) (W700)
18:39:36| Generic(non-branded) custpack: Yes
18:39:36| Allowed languages: en, id, ms, tl, vi, zs,
18:39:36| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
18:39:39| ~~~~~~~~~~ Custpack information ~~~~~~~~~~
18:39:39| Custpack: EMEA_2 (CDA102580/2) (W700)
18:39:39| Generic(non-branded) custpack: Yes
18:39:39| Allowed languages: en, cs, hr, sr, sl, sk,
18:39:39| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
18:39:55| Bypassing RSA...
18:39:55|
18:39:55| Sending db2010_cid49red_flash_r2b.bin...
18:39:55| Applet ID: 051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2
18:39:55| This is a FLASH loader
18:39:55| Flashing loaders\db2010_breakin_jhf.bin

This is start, the end is in previous post. Anyway, Se Tool repaired my phone so it's working again. I managed to change firmware from R1DB001 to R1CA021 but haven't done anything else with phone, maybe some other time. Thanks for help

[ts013]

Ok, that's nice.
Have you just flashed the firmware with SE Tool or what did you do?

[djape48]

Here is log from setool:

MAPP CXC version: R1CA021
Language Package:EUROPE_1
CDA article: CDA102295/7
CDA version: R2A
Default article: cxc1250522
Default version: R1CA021

Operator: 000-00

USERCODE:0000

Elapsed:8 secs.
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35167301xxxxx CERT:RED
LDR:051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2B
Flash ID check:890D
Flash props sent ok

DETACH CABLE FROM PHONE.
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
Trying to launch embedded bootloader...
Embedded flashloader:
COMPACT_ID_LOADER_CRIPPLED_SETOOL2_R2
Flash ID check:890D
Flash props sent ok
FOUND: R1CA021_CXC1250514_EU_1_CR
Restore from:R1CA021_CXC1250514_EU_1_CR
Elapsed:69 secs.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:4 secs.

After that phone worked normally

[Yodafone]

How do I just check my CID with XS++?

[debeliz]

yus connect it with the program, and read the log