SEMC Tool 8.4 Free

[MadMax71]

@ Neckbreaker

I´m german, will a shop from my country help you?

[logih]

Usually when a phone is turned into a brick it is not gone for good. It can be reflashed and fixed so dont give up trying. I tried to unlock my k750i with SEMC Tool 8.4 Free and it killed my phone i.e. it wouldnt turn on at all. I did manage to get it back working again. The main problem with SEMC Tool 8.4 Free is that on some CIDs like CID 49 it cannot recover phone after unlock so thats why the phones go dead. The trick arround this is to change the CDA version through xs++ so that SEUS can detect that the phone can be updated. Then SEUS can recover the phone after it is updated. Also, any unlocks i.e. SP area that were done when the phone went dead will still be active, so the phone is now unlocked. Problem solved

Hello, I have exact the same situation. here is the log:

Switch phone ON
Get phone info
Flash CID: 49
Phone KEY: A1_DB2010_49_RED
OTP CID: 49
Phone IMEI: **********
Flash ID: 890D
Switch phone ON
Write Flashloader CID49
Waiting to finish
Switch phone ON
Start Flashloader CID49
Reading flash CXC version
Version: R1CA021_CXC125952_EU_1_CL
Send FLASH application
Write GDFS Flashloader
Switch phone ON
Start GDFS Flashloader
Setup GDFS Loader
Read all codes
IMEI: *******
Unlock NCK: ******
Unlock NSCK: *****
Unlock SPCK: *****
Unlock CCK: .....
Unlock PCK: ......
Unlock ECK: ......
Relock NCK: ......
Relock NSCK: .....
Relock SPCK:......
Relock CCK:......
Relock PCK: ......
Relock ECK: ......
User code: 0000
Switch phone ON
Write Flashloader CID49
Waiting to finish
Switch phone ON
Start Flashloader CID49
Send FLASH application
Recover first flash part
ERROR: CXC version not supported for recovery!

If it is possible, could you (or somebody else) explaine me step by step how I can revive my phone? I am new in all this. Thank you very much in advance.

[MadMax71]

@ Neckbreaker
http://www.service4handys.de/index.p...roduct=A000609

[MadMax71]

Changing IMEI is illegal in Germany, so no help from me in this point.
You should go to a handyshop near you and let them make the unlock, that will cost you around 20€.
If you try to unlock your phone with cracked software you have to buy cable- that cost 15€ and the risk that you brick your phone is high.

Your choice!

P.S. i´m from Bielefeld and next time just write me a PM in german but not here in the forum.

[m1ch43lzm]

@logih
Just reflash MAIN R1CA021_CXC125952_EU_1_CL
K750_R1CA021_MAIN_EU_1_CL_RED49

You can use XS++ and DCU-60 cable to do this
After you flash MAIN, remove battery, put battery back, turn on phone, and enter "Unlock NCK" code manually

Press <**< (< means moving joystick left), and enter the NCK code given by the program

[chripopper]

what is XS++ ?

Search the forum and i promise you will find out!

[zzzn00bzzz]

I had no problems with SEMC 8.4 on my W810, I just did clear SP lock. and it worked for me :x

[kondronaute]

@ logih :
your phone is not dead write again a main supported by semctool (see the list) and retry, you can also just write the main and it will go again :p

[DUSKnenixs]

better to use original...cracked one maybe kill phones

[DUSKnenixs]

like it happened to me on k310i i have killed one....