Flashing w/Far cid49 w810 trouble. REWARD offered for help

[Splinter_C]

Customizing is like intializing the FS. Basically it's only copying some customization files to a certain place in the file system (tpa/preset/custom). You can do this in two ways:

1. with XS++ by putting a check at Customize file system (note that this involves bruteforce!), or
2. by manually upload the customization files using the FAR + SEFP method. See below for detailed instructions on how to unbrand.

This tutorial explains step-by-step how to use FAR + SEFP to edit the files in your phone's file system. So now you know the context.

1. Premeasures:install USB Flash drivers (by installing SEUS for example)
2. install FAR-manager 1.70 here
3. extract the SEFP plugin (first SEFP v01004, then SEFP v010051 over it) to the plugin folder (C:\Program Files\Far\Plugins normally)
4. Extract den_po's CID49 pack db2010cid49_4_alpha.rar.zip to FAR\plugins
5. Get XS++ and a proper MAIN firmware(use same version as your FS !), download here:
-download the latest XS++
5. archive: http://xsse.4shared.com/ pass = se-nse
- site: WWW.IPROTEBE.CZ
- else check the Stickies in the Firmware & Flasing subforum here on SE-NSE...
6. Remove your SIM-card and memorystick, just in case..

Flash break-in loader:
7. Open XS++, connect, ONLY flash your MAIN with w810_p3k_dcu.49R.ssw (located in CID49 package).

This is a break loader. If you flash this into your phone, your phone cannot be turned on anymore because it's not a real firmware, but only a workaround intended to access the filesystem without bruteforce (using den_po's CID49 pack for the SEFP plugin for FAR-manager). It's only 5 flash blocks, should not take more than 30secs. Just choose STOP if it hangs on 100%.
8. Remove your battery for 5secs and after that put it back in.

Customizing with FAR+SEFP:
9. Open FARmanager, and press F11
10. Choose SEFP plugin
1. If you get the error: "Unknown exception", Exception address: 0x7C812A5B...... The plugin will be Unloaded!
This is a bug. It's because you don't have any COM-ports, so create a fake COM-port connection. I did it with my BT Dongle. Alternatively, here is a mini howto create a fake COM-port by Cold & Flu Relief.
2. if you get the error: "<BIldr> can be used with Service Cable ONLY".... browse to the SEFP folder and patch sefp.dll with sefp0.10.0.51patch.exe.
3. if you still get any errors, and just want a working phone back, skip this part and proceed at step 16.
11. Opening SEFP:


choose Bootscript: w300_w810_z550_cid49 and press Enter The Matrix.
After a while you'll be in the w810i, if not, try again, check settings above.
12. Choose /FS/, now you'll can customize everything you want; camdriver/ audiodriver/ etc.
See below for some tips, or check out Links.
13. When done, Go back to root (choose '..' all the time) until FAR asks to exit CSFS loader, choose yes.
14. Exit FAR-manager
15. Disconnect cable and remove your battery for 5secs.

Flash real MAIN:
16. Now go back to XS++ and connect your w810i.
17. Now only flash your real MAIN file (i.e. W810_R4EA031_MAIN_GENERIC_HN_RED49.mbn, 344 flash blocks).
Don't check Customize File System! This will only take about 2 minutes.

If all went right, you're done, you have customized your w810i WITHOUT bruteforce!