Hi,
i 've tried to flash den_po's breakin loader using xs++v15 in order to
do debranding.
After it said "finishing flash" nothing happened.
I hit "stop" as posted in the tutorials and it said "++Error flashing failed".:confused:
Then I disconnected the phone.
Afterwards it wasn't either possible to access the FS with Far170, or to switch on the phone.:eek:
Fortunately it was possible to restore the original MAIN via SEUS and the
phone is working again.:cool:
What did I wrong.
Please help a newbi ;)
Thanks
kram
LOG:
23:38:24| XS++ v1.5 Ready !
23:38:46| Attempting to open the interface...
23:38:46|
23:38:46| Turn off phone
23:38:46| Hold C Button on phone and connect phone.
23:38:46| You have 30 seconds.
23:38:46|
23:38:53| PORT STATUS: ACTIVE
23:38:54| Baseband ID: 8040
23:38:54| Hardware Platform: db2010 Marita compact
23:38:54| Protocol Version: 3.1
23:38:54| AutoReturnCollectingSending loaders\db2010_cid00_prodid_p3k.bin...
23:38:54| This is a PRODUCTION_ID loader
23:38:54| ***** Read flash vendor & id (cmd 0D)
23:38:54| ***** Read otp (cmd 24)
23:38:54| Activating GDFS...
23:38:55| phone name detected
23:38:55| Return
23:38:55| PHONE INFO
23:38:55| DBID: db2010
23:38:55| OTP CID: 49
23:38:55| EROM CID: 49
23:38:55| EROM color: Red
23:38:55| IMEI: 35906400xxxxxx
23:38:55| Phone: W810
23:38:55| Operator: T_MOB_INT_A
23:38:55| CDA: CDA102494/55 R8A
23:38:55| Firmware: R4DB005
23:38:55| EROM: n/a
23:38:55|
23:38:55| Ready for operation!
23:39:31| Sending loaders\db2010_cid49red_flash_r2a003.bin...
23:39:31| This is a FLASH loader
23:39:31| ***** Read flash vendor & id (cmd 0D)
23:39:31| ***** Read otp (cmd 24)
23:39:31| +++ Now flashing firmware main...
23:39:31| Sending flashfile D:\Download\handy\far kram\db2010cid49_4_alpha\w810_p3k_dcu.49R.ssw
23:39:31| 5 flashblocks
23:39:33| Finishing flash
23:39:51| ++ Error: Flashing failed
23:39:51| Disconnected... Unplug the phone
23:44:57| Shutting down...
Results 1 to 10 of 10
-
07-03-2007 #1Recently Initiate
- Join Date
- Jun 2007
- Device
- -
- Posts
- 5
- Thanks
- 2
- Thanked 0 Times in 0 Posts
W810 problem flashing breakin loader: ++Error: Flashing failed. pls help
Last edited by kram; 07-03-2007 at 04:25 PM. Reason: better topic
07-03-2007 #2Member
- Join Date
- Jan 2007
- Device
- k750@w800 (R1BD) with elfs, patches...
- Posts
- 81
- Thanks
- 20
- Thanked 10 Times in 8 Posts
Weird... Is the phone branded with T-Mobile? That might cause an error. The "finishing flash" will go on for ever so you have to hit "stop" and it will always say "flashing failed". And about the phone not turning on, it's completely normal as long as the breakin ssw is inside.
[EDIT] Maybe you should try to find a newer version of SEFP.
07-03-2007 #3Advanced user
- Join Date
- Mar 2007
- Device
- W810i, W550i
- Posts
- 436
- Thanks
- 5
- Thanked 68 Times in 60 Posts
try XS++ 1.2 it works fine for me, if you still get the error then try another pc!
07-03-2007 #4Banned
- Join Date
- May 2007
- Device
- -
- Posts
- 31
- Thanks
- 0
- Thanked 4 Times in 4 Posts
Indeed , getting Flashing Failed Error message after sending the 5 flashblocks specific to the Break-in-loader is an Actual XS++ bug...see a drawback ...that should be resolved in further releases...SO DON'T WORRY ABOUT A LOT ..
Originally Posted by kram
As for what you said , u tried Far , afterwards ,but in Vein ...!! did u have your Far Patched ...and did you use The RIGHt BOOT SCRIPT...that is ..W330_W810_Z550_ ????
The Following User Says Thank You to mourad_ada For This Useful Post:
07-03-2007 #5Recently Initiate
- Join Date
- Dec 2006
- Device
- -
- Posts
- 17
- Thanks
- 0
- Thanked 2 Times in 2 Posts
make sure you have the latest SEFP. And check what cable you use. DCU-60 or service! make sure it's set right. You can try to use SEMC 8.4, it worked for me.
07-04-2007 #6Recently Initiate
- Join Date
- Jun 2007
- Device
- -
- Posts
- 5
- Thanks
- 2
- Thanked 0 Times in 0 Posts
w810: perhaps a FAR problem: FS access freezes
Hi,
thanx for reply
yes, it's a T-mobile branded phone
xs++ 1.2 had the same results
perhaps you're right an did correct braekin-flashing and the problem is FAR-related.
Here's what happended in FAR
- set up FAR copying sepf44 & sepf51 doing den_po's patch afterwards.
- started far
- W300_W810_...
- Enter the matrix
- far told me to connect the w810 pressing c
- connected w810 via USB
- Folder MAIN/FS appear in left window
- clicking FS
- SE Flash pluging window appears: Command pprogress 1
- NOTHING HAPPENS and Far freezes :confused:
Any further idea ???
07-04-2007 #7Advanced user
- Join Date
- Mar 2007
- Device
- W810i, W550i
- Posts
- 436
- Thanks
- 5
- Thanked 68 Times in 60 Posts
try another system or bruteforce, if anyone has another ideea please share :)
The Following User Says Thank You to Khaba For This Useful Post:
07-04-2007 #8Recently Initiate
- Join Date
- Feb 2007
- Device
- -
- Posts
- 3
- Thanks
- 0
- Thanked 1 Time in 1 Post
Just a thought, do you have enough battery power?
07-04-2007 #9Recently Initiate
- Join Date
- May 2007
- Device
- -
- Posts
- 1
- Thanks
- 0
- Thanked 0 Times in 0 Posts
k
hi, i'm looking for flash themes for weeks!
can someone help me? Where can i find flash themes? i know that in this page are some, but i need some more!
thx, Zatonyisz
07-04-2007 #10Banned
- Join Date
- May 2007
- Device
- -
- Posts
- 31
- Thanks
- 0
- Thanked 4 Times in 4 Posts
try this ..
It's really worth trying why not ...just get to C:\Program Files\Far\Plugins\SEFP double-click on sefp0.10.0.51patch Originally Posted by kram
and click on "UNDOT IT!" ...that would restore the original sefp.dll ..
and try once again connecting ur PHONE THRU FARMANAGER..
THAT WOULD WORK BUT NOT GARANTEED ...JUST Tested ON K310 and truly passed !!
Hopefully you manage to break into ur phone FILE SYSTEM !
Best Regards .
Mourad
