Help needed

[_Adrian_]

Hey guys..
my phone started acting weird today and then it froze.
so i decided to reflash it.
now its not working.
First all i got was a flashing back light and now nothing.
Its a K790a and using SE lite V1.11 using R6BC002 main file and a vkp made from it.
Even tried XS but it hangs.
With SE it fails where the bootloader gets loaded, and never makes it past that point.
any ideas guys ??
i been workin at it most of the day and still no luck
thanks guys

[SeaMonkey]

Hey guys..
my phone started acting weird today and then it froze.
so i decided to reflash it.
now its not working.
First all i got was a flashing back light and now nothing.
Its a K790a and using SE lite V1.11 using R6BC002 main file and a vkp made from it.
Even tried XS but it hangs.
With SE it fails where the bootloader gets loaded, and never makes it past that point.
any ideas guys ??
i been workin at it most of the day and still no luck
thanks guys

Did you backup GDFS,if you do just restore GDFS

[_Adrian_]

sure did...
but that dont work either

[SeaMonkey]

sure did...
but that dont work either

Try to fill your battery full .And try with Setool read your phone.
If you succeed to Setool read your phone post log here first

[Khaba]

try a full flash, MAIN, FS and custom pack, and the see what happens.

[_Adrian_]

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:3522080122XXXX CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:49 PAF:1 IMEI:3522080122XXXX CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
Abort all operations.
Elapsed:420 secs.

Thats whats going on, any ideas ??

[simox]

BOOTROM MODE DETECTED

When you connect the phone press the C key on phone and not the 2+5 keys. Then try to reflash the phone. Also you can try XS++ instead of SETool2 Lite.

[_Adrian_]

20:40:29| XS++ v3.1 (Darwin) Ready !

20:40:29| Executed on Microsoft Windows Vista

20:40:36|

20:40:36| Attempting to open the interface...

20:40:36|

20:40:36| TURN OFF PHONE!

20:40:36| Hold 'C' button on phone and connect phone NOW.

20:40:36| You have 30 seconds...

20:40:36|

20:40:40| Baseband ID: 9900

20:40:40| Protocol Version: 3.1

20:40:58| Sorry, your phone is NOT SUPPORTED

20:40:58| Sendinging shutdown signal to phone...

20:41:00| Shutting down...

thats from XS++
i can flash it overand over, but it never powers up :@

[_Adrian_]

When you connect the phone press the C key on phone and not the 2+5 keys. Then try to reflash the phone. Also you can try XS++ instead of SETool2 Lite.

it wont do nothing when im holding C
but i got it further than i did...
Started with holding 2+5 and then was using C through the rest of the process, but this is what happened next !!!

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit Index of ./ and buy FULL.

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:3522080122XXXX CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
OTP LOCKED:1 CID:49 PAF:1 IMEI:3522080122XXXX CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
INT LDR:DB2020_PRELOADER_FOR_SETOOL2
LDR:DB2020 LOADER FOR SETOOL2
Flash ID check:897E
Flash props sent ok
writing C:\Users\acer\Documents\Cell phone Stuff\setool2lite\qamaker\K790_R6BC002_MAIN_GENERI C_EV_RED52.mbn
CURRENT FLASH FILE CID:52
SSW uses complete hash, hash len is:9200
Will flash 460 blocks...
verify block error
last blk:45230000,00010000
Elapsed:642 secs.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:72 secs.
Abort all operations.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:53 secs.

as you can see tried to re-flash the phone with no success...
any other thoughts or ideas ??
phone is now dead and wont even flash

[SeaMonkey]

it wont do nothing when im holding C
but i got it further than i did...
Started with holding 2+5 and then was using C through the rest of the process, but this is what happened next !!!

as you can see tried to re-flash the phone with no success...
any other thoughts or ideas ??
phone is now dead and wont even flash

Maybe you have corrupted firmware, check with babeck ( here you have - Top Sony Forums )your main and FS