K800i problem solving..

hi, i am new here at TopSony.. :)

ok, i am not new into modding/flashing SE phones since i own a W810i and a W880i phones..
however, the sister of my friend owns the K800i.. and then she told me that one day, the
phone stops responding and became dead (it cannot be turn on).. i do not have the full
story as to why the phone became dead.. but since i know some on flashing, i checked it
today..

the phone's IR LED only blinks once when i tried to power it up.. what does that mean?
i tried to read the phone using SETool 2 Lite v1.08 and got this line:

Code:

---

welcome to setool2 lite edition v 1.08
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:359087xxxxxxxx CERT:RED
FLASH CID:52 COLOR:RED
 
MAPP CXC article:
MAPP CXC version:
Language Package:
CDA article:
CDA version:
Default article:
Default version:
 
Operator: 000-00
 
Elapsed:416 secs.

---

*this was done with the 2+5 button press instead of the C button..

then i tried to read the GDFS and got this line after the above lines:

Code:

---

Will backup GDFS now.
ChipID:9900,EMP protocol:0301
RECOVERY BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:359087xxxxxxxx CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:18 secs.

---

can anyone pinpoint the problem? do i need to flash a new FS and MAIN? or probably a
GDFS and/or EROM as well?

it is the erom..

just as the majority of my thought was.. hhmmm, any idea on how to solve it? should i try
to directly flash an EROM? if so, what EROM would you recommend? and i can only do it with
SETool 2 Lite since XS++ can't detect the phone well enough..

Check out this tutorial: REPAIRING EROM GUIDES for most sonyericsson phones.

i had this error though

Code:

---

CSloader refused to start GDFS services,error is:29

---

Try with this steps plz help... k810 is dead what can i do ? - Top Sony Forums .

Have a nice day

i did what that post told to do.. i managed to open the port using the C button on XS++
unlike it was before.. however, the moment XS++ detected it, it never managed to finish
(up until now as i type this reply) and got stuck with this line: "Did not receive 0x5a. Continuing"

what seems to be the problem there?

Not receiving 0x5a could disappear when you try it again or with an other version from XS++.

Have a nice day

ok.. i'll keep on trying it.. thanks for that one.. i might come back to post some updates..
thanks again.. :)

EDIT:
i only have the 3.2 (Crystal) and the 3.1 (Darwin) versions.. if you do not mind, do you
happen to know which of this two is somewhat better when it comes to that procedure?

You can tried this:

Refresh your phone by taking out the battery and reinserting it, then try again.
If it doesn't work, have you installed the USB drivers?

USB Flash Driver Installation - Guide

Have a nice day

i think i did.. using the ggsemc.inf contained on the drivers folder of setool2lite.. i would try
that guide on my vista laptop..

thanks again..

Quote:

---

Originally Posted by shusakupen

ok.. i'll keep on trying it.. thanks for that one.. i might come back to post some updates..
thanks again.. :)

EDIT:
i only have the 3.2 (Crystal) and the 3.1 (Darwin) versions.. if you do not mind, do you
happen to know which of this two is somewhat better when it comes to that procedure?

---

Use 3.1 , because 3.2 can mess your phone.

Have a nice day

hhhmmm, now, i happen to notice one thing.. it's somewhat standard now.. when i do follow
the procedures, i noticed that if i didn't remove the battery before using XS++, the line:
"Did not receive 0x5a. Continuing" occurs almost all the time and then hangs XS++
however, when i do remove the battery before using XS++, it doesn't detect the phone..

i wonder if i was still missing something here.. i know i did install ggsemc.inf to detect USB
Flash memory..

i managed, at last, to make it detectable.. however, XS++ only showed two lines and never
responded after it.. the two lines are:
Baseband ID: 9900
Protocol Version 3.1
and XS++ stop responding after that..

could it be that the phone cannot be detected after all? just like what SEUS says, that the
phone identification cannot be confirmed..

could it be that the Flash IC was already out-of-luck and died?

Did you press c button to detect or 2+5?

Have a nice day