How to unbricked my P1!

Hey guys..... WOW.. my first thread ever... n that also abt unbricking P1i.... Nice

I had bricked my brand new barely 2 months P1i during restoring my back-up using Sony PC Suite. The phone would not boot but had the back light on and so were the keypad light. Thats it.. it waz bricked.
Then after lots of research (Google) i had done a hybrid of them....

First you need to download XS++ from here..

http://www.se-nse.net/gbrooks3/XS++/download.php

Then download the SEUS from the official sony web coz it is the latest....

Download the P1i ressurection file from here.....

http://www.se-nse.net/gbrooks3/XS++%20Dev/P1_CCPU.zip

After you have XS++, Ressurection file, SEUS, you are ready to unbrick your phone..:)

Open XS++ :
i) tick smartphone connect
ii) press connect
iii) remove your SIM card, remove and re-insert ur battery after 2 sec.
iv) connect the USB cable to P1i while holding "C" button.
v) go to flash section
vi) load the P1i CCPU.zip file under smartphone flashing section, DO NOT UNZIP THE FILE.
vii) tick flash CCPU (remember, ONLY TICK CCPU)
viii) press "flash PDA" and wait for it to finish

After flashing is done, run the SEUS service by following the instructions on the application.
Note: if SEUS says u already have the firmware, just press continue anyway.
After SEUS is done.. you have a brand new P1i!!!.
you will lose all ur user data though.

The above procedure is what I did to unbrick my P1i.....
Hope this helps those in need....Just remember to fully charge your battery before doing the procedure... dont worry if the light is not there during charging coz its charging.. believe me...

Thanks to se-nse.net, Lowyat.net, and topsony.com

Enjoy...!!!!:D:D

you can also unbrand the phone using this process but the only thing you must do is that in the xs++ you choose the option of changing the CDA and put a generic one like "generic world 1" and finish the process of this tutorial!

pd: only unbranding NOT UNLOCKING!

The thread is going to be sticky so any questions Discussions all about uiq3! - Top Sony Forums in there!!

i got my p990i dead: i went up the mountain had an overnight, and when i went home the following day, my phone just (got fever) it turn hot, then it went empty bat. with alarm on, and by the time its alarmed it didnt turned on, upto now it didnt turned on for 3 months, any help with my p990i?
please?
got some xs++, but i dont have the ccpu for p990i, the xs++ when in flash it says "a brown phone?" but i really need ccpu, cause i tried p1i ccpu it can read through it but for phase 3 xs++ tells that its not compatible..
anybody got ccpu p990i? got this phone made in france..
----------------------------------------------------------------------------------
08:07:06| Executing SEMC Smartphone Operations!

08:07:06| Please hold boot key ('@' or 'C') and connect device...

08:07:17| Master Port detected: COM6

08:07:17| Slave Port detected: COM7

08:07:17| Opening Port!

08:07:17| INIT MASTER...OK!

08:07:17| PHONE INFO SAMPLED...OK!

08:07:17| EPOC APPLET HEADER SENT...OK!

08:07:17| APPLET BODY SENT...OK!

08:07:17| SHUTTING DOWN MASTER...OK!

08:07:19| Baseband ID: 7100

08:07:19| Protocol Version: 3.1

08:07:19| NEW SECURITY PHONE DETECTED! SWITCHING...

08:07:20| Speed set to 460800

08:07:20|

08:07:20| Sending db2000_cid03_prodid_p3b.bin...

08:07:22| Applet ID: 070410 1354 NPACXC125871_DB2000_PRODUCTIONIDLOADER_P3B

08:07:22| This is a PRODUCTION_ID loader

08:07:22| Activating GDFS...

08:07:22| Cannot open GDFS

08:07:22| Activating GDFS...

08:07:22| Cannot open GDFS

08:07:22| Activating GDFS...

08:07:22| Cannot open GDFS

08:07:22| Warning: IMEI name does not match GDFS name (IMEI:P990 GDFS:n/a)

08:07:22| ...using IMEI name

08:07:22|

08:07:22| Profiling EPOC smartphone...

08:07:22| Platform: DB2001

08:07:22| OTP CID: 49

08:07:22| EROM CID: 298909995

08:07:22| EROM Color: Unknown

08:07:22| IMEI: 35959300xxxxxx

08:07:22| Phone ID: P990

08:07:22| Part Number: n/a

08:07:22| Phone smartphone version: R1A10

08:07:22| Phone software version:

08:07:22| Processing Unit:

08:07:22| Organizer:

08:07:22| CDA:

08:07:22| Activating GDFS...

08:07:22| Cannot open GDFS

08:07:22| Ready for operation!
---------------------------------------------------------------------------------------
anybody got some idea for this problem? i need ccpu p990i please...

08:10:39| A Brown Smartphone? Joking?
08:10:39| Error: Failed to send CSLoader!
08:10:39| FSX Shutdown!
08:10:41| Disconnected... Unplug the phone


++++EDITED BY ALLAN92++++
Dont make double posts use edit!

Thats your problem that your phone has brown firmware your only hope is to get a setool box and make a fullflash! with brown firmwares!

i didnt even know this is a brown firmware.. can you help me out with this? if its ok??
how much would it cost me? does the service centers have this tool box?
step by step guide... maybe i cant afford se tool box, but is there any other way using usb cable?

Quote:

---

Originally Posted by pinky_brai

Hey guys..... WOW.. my first thread ever... n that also abt unbricking P1i.... Nice

I had bricked my brand new barely 2 months P1i during restoring my back-up using Sony PC Suite. The phone would not boot but had the back light on and so were the keypad light. Thats it.. it waz bricked.
Then after lots of research (Google) i had done a hybrid of them....

First you need to download XS++ from here..

http://www.se-nse.net/gbrooks3/XS++/download.php

Then download the SEUS from the official sony web coz it is the latest....

Download the P1i ressurection file from here.....

http://www.se-nse.net/gbrooks3/XS++%20Dev/P1_CCPU.zip

After you have XS++, Ressurection file, SEUS, you are ready to unbrick your phone..:)

Open XS++ :
i) tick smartphone connect
ii) press connect
iii) remove your SIM card, remove and re-insert ur battery after 2 sec.
iv) connect the USB cable to P1i while holding "C" button.
v) go to flash section
vi) load the P1i CCPU.zip file under smartphone flashing section, DO NOT UNZIP THE FILE.
vii) tick flash CCPU (remember, ONLY TICK CCPU)
viii) press "flash PDA" and wait for it to finish

After flashing is done, run the SEUS service by following the instructions on the application.
Note: if SEUS says u already have the firmware, just press continue anyway.
After SEUS is done.. you have a brand new P1i!!!.
you will lose all ur user data though.

The above procedure is what I did to unbrick my P1i.....
Hope this helps those in need....Just remember to fully charge your battery before doing the procedure... dont worry if the light is not there during charging coz its charging.. believe me...

Thanks to se-nse.net, Lowyat.net, and topsony.com

Enjoy...!!!!:D:D

---

========================================

this was definitely the fix for my phone! after 4 months of searching the net and asking some of the repair shops, many thanks to you pinky_brai... you rock..!

Sounds like a gr8 solution! but my question is: can i use this method to change CDA of P1i to Arabic ? even with some changes ?

Hi there people.... I m glad i waz able to help some of u guyz....

1- Perform a back-up of your phone via the PC Suite (or however you prefer), as you are going to wipe all of the phones C drive.
2-Run the Sony Ericsson Update Service (SEUS), click on the icons matching your phone, when prompted pull the battery out and put it back in, when prompted plug the cable into your phone whilst holding down C (this is either the letter C on the keyboard, the Cancel button or even the @ internet button). Once it’s found your phone it’ll will either prompt you to update the firmware or inform you that you have the latest. Either way, quit SEUS without doing anything else. (This will force your PC to find the drivers required for your phone)
3-Run XS++, click on the SMARTPHONE CONNECT box, and press Connect. The box on the left will tell you what to do, but it’ll be similar to step 2.

-Once connected you now need to select the new CDA for your phone:
W960 - CDA 162032/1
P1 - CDA 162022/1
P990 - CDA 162007/1
M600 - CDA 162011/1
W950 - CDA 162014/1
and hit Run Script. (They all have GW1 in the script name, however you can choose any of the others, but I recommend the Generic World 1 scripts)

5-You can now close XS++, I recommend that you don’t touch anything else in XS++!
6-Now run SEUS again, this time do the update on your phone. Boot up your phone to the Sony Ericsson or Walkman startup screens
7-Boot up your phone to the Sony Ericsson or Walkman startup screens. Goodbye Vodafone, Orange or o2
8-Restore the backup of your phone
(I do not know a way to download pictures from the Web site and want Iraslani I have tried and been successful:))

thanks for the info..

Hi, I need some help. My P1i has bricked after running SEUS. I have tried backing up the GDFS using XS++ but it won't even open:

14:01:19| XS++ v3.1 (Darwin) Ready !
14:01:19| Executed on Microsoft Windows XP
14:01:38| Executing SEMC Smartphone Operations!
14:01:38| Please hold boot key ('@' or 'C') and connect device...
14:03:05| Disconnected... Unplug the phone
14:03:37| Executing SEMC Smartphone Operations!
14:03:37| Please hold boot key ('@' or 'C') and connect device...
14:03:40| Master Port detected: COM7
14:03:40| Slave Port detected: COM8
14:03:40| Opening Port!
14:03:40| INIT MASTER...OK!
14:03:40| PHONE INFO SAMPLED...OK!
14:03:40| EPOC APPLET HEADER SENT...OK!
14:03:40| APPLET BODY SENT...OK!
14:03:40| SHUTTING DOWN MASTER...OK!
14:03:42| Baseband ID: 7100
14:03:42| Protocol Version: 3.1
14:03:42| NEW SECURITY PHONE DETECTED! SWITCHING...
14:03:43| Speed set to 460800
14:03:43|
14:03:43| Sending db2000_cid03_prodid_p3b.bin...
14:03:44| Applet ID: 070410 1354 NPACXC125871_DB2000_PRODUCTIONIDLOADER_P3B
14:03:44| This is a PRODUCTION_ID loader
14:03:45| Activating GDFS...
14:03:45| Cannot open GDFS
14:03:45| Activating GDFS...
14:03:45| Cannot open GDFS
14:03:45| Activating GDFS...
14:03:45| Cannot open GDFS
14:03:45| Warning: IMEI name does not match GDFS name (IMEI:P1 GDFS:n/a)
14:03:45| ...using IMEI name
14:03:45|
14:03:45| Profiling EPOC smartphone...
14:03:45| Platform: DB2001
14:03:45| OTP CID: 52
14:03:45| EROM CID: 53
14:03:45| EROM Color: Red
14:03:45| IMEI: 35xxxxxxxxxxx
14:03:45| Phone ID: P1
14:03:45| Part Number: n/a
14:03:45| Phone smartphone version: R1C01
14:03:45| Phone software version:
14:03:45| Processing Unit:
14:03:45| Organizer:
14:03:45| CDA:
14:03:45| Activating GDFS...
14:03:45| Cannot open GDFS
14:03:45| Ready for operation!
14:04:05|
14:04:05| Sending db2001_cid53red_cs_p1e.bin...
14:04:22| Applet ID: 070405 1245 NPA1_CXC1327363_1_SEMC_CS_LOADER_1_P1E
14:04:22| This is a CHIPSELECT loader
14:04:22| Activating loader...
14:04:22| Activating GDFS...

It then just hangs?

I tried the CCPU file as suggested above to no avail, as it gets to flash number 23 out of 107 and again just hangs. Have tried running SEUS again, but equally says I have the most up to date firmware. Any suggestions? Please. Am reluctant to give Sony Ericsson Service Centre money after SEUS screwed up the phone. FYI, The phone won't switch on, the keyboard lights up and the screen but does not boot top Sony Ericsson screen.

Thanks.

I had bricked my brand new barely 2 months used P1i during restoring my back-up using Sony PC Suite. The phone would not boot but had the back light on and so were the keypad light. Thats it.. it waz bricked.

thx. it was helpfull

It did not work for my P1i, mine still bricked n the SEUS doesn't support P1i anymore, help me to unbricked my phone, coz thiz phone is awesome, n I love this phone.