Printable View
In order to upgrade from CID51 to CID 52 use SEUS (Sony Ericsson Update Service). It's a simple and safe procedure.Quote:
Originally Posted by akshayy
After upgrade to CID52 by SEUS you can customize the new system with SETool2Lite 1.08 and XS++ 2.2.
www.se-nse.net Link here.
No, v3 Is the best !!
How can download custpack for my P1i? i need singapore version.
How can i get V3 and what is V3? XS++ V3??
Quote:
Originally Posted by DXX-T
Sorry, I don't own a SMARTPHONE, so I can't answer your question.Quote:
Originally Posted by ccmak
v3, XS++v3 BETA, New version ;)
Hello All,
Very, very thanx about these Tutorial, I very good!
I have a W200a, and I want to change my language pack, but I have a problem, because I'm in French Guian (South America) Very Very near to Brazil, and I need a language pack that have a Brazilian Portuguese, French, English and Spanish.
I seed a Europe_1 a Portuguese language that is there is the Portugal Portuguese, that is very very diferent from the brazilian.
Thanx...
ricardoab: Have a look at the languages description on the main page to find out what firmware you have to flash to get your desired language.
The problem is: W200 is not supported by XS++ as far as i know. Unfortunately I'm not sure if you can use FAR or SE Tool lite, I never used that type of phone.
Can this tool upgrade CID49 to CID51?
yes. put the appropriate firmware file in the main slot, and the CID will be updated
:)hi...
how can i change the color of my phone from brown to red? which software should i use?
can i apply patches n XS++? can i change the drivers in my phone even if it is brown? what should i do to apply the drivers in my phone?
Thanks...:)
if i flash my k550 red52 with xs++ v2.2?
I tried to flash my w700i (originally R1DB001) with xs++, W700_R1CA021_MAIN_EU_1_CR_RED49 as main, W700_R1CA021_FS_EMEA_2_RED49 as FS, and customization w700 EMEA_2 and xs stuck at Activating filesystem. I stoped procedure after 30 minutes, and phone couldn't turn on in phone mode (configuration error...). When select music mode at startup (works normally) and enter service info/software info - it is r1ca021. How can I fix my phone? This is my first flashing, maybe I shouldn't do it :)
thank you i want to flash my k610i to w660
but how?
djape: Try using an older version (1.2 or 1.5)
Tried xs 1.5 but everytime stops here:
18:38:17| Ready for operation!
18:38:39| Starting Loader Unlock Hack...
18:38:39| ***** R3L
18:38:39| Cannot open CID36_00_R3L.bin
18:38:39| Wait for loader hello
18:38:54| ++ Error: Flashing failed
18:38:54| Disconnected... Unplug the phone
18:38:56| Shutting down...
Now I tried xs 3.0 beta and another failure:
19:03:06| Done uploading
19:03:06| Sending shutdown command to phone...
19:03:06| Customizing was SUCCESSFUL!
19:03:06|
19:03:06| Disconnect phone from USB-port and wait for
19:03:06| further instructions.
19:03:06| You have 10 seconds.
19:03:06|
19:03:16| Open the battery-cover and reinsert the battery.
19:03:16| Hold C Button on phone and connect phone again.
19:03:16| You have 30 seconds.
19:03:16|
19:03:23| Baseband ID: 8040
19:03:23| DB2010 Marita compact
19:03:23| Protocol Version: 3.1
19:03:23| Phone has restarted successfully...
19:03:23|
19:03:23| Sending db2010_cid49red_flash_r2b.bin...
19:03:23| Applet ID: 051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2B
19:03:23| This is a FLASH loader
19:03:23| Flashing breakinfirm\W700_R1CA021.bin
19:03:23| Header type: BABE
19:03:23| 2 flashblocks
19:03:23| Binary acknowledge failed with: 15
19:03:23| Failed
19:03:35| Error: Flashing failed
19:03:35| Disconnected... Unplug the phone
19:03:39| Shutting down...
Stupid w700
Please post up the log when you just connect the phone.
A log of the identifying process done with SE Tool lite would be nice too.
18:39:11| XS++ v3.0 beta (Sinyar) Ready !
18:39:11| Executed on Microsoft Windows XP
18:39:19|
18:39:19| Attempting to open the interface...
18:39:19|
18:39:19| TURN OFF PHONE!
18:39:19| Hold 'C' button on phone and connect phone NOW.
18:39:19| You have 30 seconds...
18:39:19|
18:39:25| Baseband ID: 8040
18:39:25| DB2010 Marita compact
18:39:25| Protocol Version: 3.1
18:39:25|
18:39:25| Sending db2010_cid00_prodid_p3l.bin...
18:39:26| Applet ID: 061113 1250 ALUCXC125872_COMPACTPRODUCTION_ID_LOADER P3
18:39:26| This is a PRODUCTION_ID loader
18:39:26| Activating GDFS...
18:39:26| Phone name detected!
18:39:26|
18:39:26| Profiling SEMC phone...
18:39:26| Baseband ID: DB2010
18:39:26| OTP CID: 49
18:39:26| EROM CID: 49
18:39:26| EROM Color: Red
18:39:26| IMEI: 35167301xxxxxx
18:39:26| Phone ID: W700
18:39:26| Network: EMEA_2
18:39:26| CDA: CDA102295/7 R2A
18:39:26| Firmware Version: R1CA021
18:39:26| EROM: n/a
18:39:26| Ready for operation!
18:39:36| ~~~~~~~~~~ Custpack information ~~~~~~~~~~
18:39:36| Custpack: APAC_1 (CDA102580/101) (W700)
18:39:36| Generic(non-branded) custpack: Yes
18:39:36| Allowed languages: en, id, ms, tl, vi, zs,
18:39:36| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
18:39:39| ~~~~~~~~~~ Custpack information ~~~~~~~~~~
18:39:39| Custpack: EMEA_2 (CDA102580/2) (W700)
18:39:39| Generic(non-branded) custpack: Yes
18:39:39| Allowed languages: en, cs, hr, sr, sl, sk,
18:39:39| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
18:39:55| Bypassing RSA...
18:39:55|
18:39:55| Sending db2010_cid49red_flash_r2b.bin...
18:39:55| Applet ID: 051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2
18:39:55| This is a FLASH loader
18:39:55| Flashing loaders\db2010_breakin_jhf.bin
This is start, the end is in previous post. Anyway, Se Tool repaired my phone so it's working again. I managed to change firmware from R1DB001 to R1CA021 but haven't done anything else with phone, maybe some other time. Thanks for help
Ok, that's nice.
Have you just flashed the firmware with SE Tool or what did you do?
Here is log from setool:
MAPP CXC version: R1CA021
Language Package:EUROPE_1
CDA article: CDA102295/7
CDA version: R2A
Default article: cxc1250522
Default version: R1CA021
Operator: 000-00
USERCODE:0000
Elapsed:8 secs.
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35167301xxxxx CERT:RED
LDR:051207 0928 NPACXC1250165_1_SEMC_COMPACTFLASHLOADER R2B
Flash ID check:890D
Flash props sent ok
DETACH CABLE FROM PHONE.
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"
ChipID:8040,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:49
Speed:921600
Trying to launch embedded bootloader...
Embedded flashloader:
COMPACT_ID_LOADER_CRIPPLED_SETOOL2_R2
Flash ID check:890D
Flash props sent ok
FOUND: R1CA021_CXC1250514_EU_1_CR
Restore from:R1CA021_CXC1250514_EU_1_CR
Elapsed:69 secs.
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:4 secs.
After that phone worked normally
How do I just check my CID with XS++?
yus connect it with the program, and read the log
Then what do I do to disconnect the phone? Is there a disconnect button?
yes ther is, start the program and you will see it.
OK, I did it, just in case I did anything wrong, I did it with my old K510.
Now I know it's CID49
Would I need to debrand it (It's Vodafone branded) to add files to it (eg. New startup sound) and what directory do I put the startup sound? And would it require bruteforce? (Where you have to wait about 5 hours...)
Quote:
Originally Posted by Yodafone
if you wont to debranded you need flash it with non branded soft, i think you dont need to change your soft to change start up sound.
For changing you start up sound you need to upload to
tpa//preset//system//settings
using Far manager
The default start up sound is located at:Quote:
Originally Posted by Yodafone
\TPA\PRESET\SYSTEM\SETTINGS\STARTUP_SOUND_SEMC.mid
just replace it with a new midi file of your choice and rename it to STARTUP_SOUND_SEMC so thats it...
you can also use XS 3.0 (FSX) its much safe!
Does it bruteforce though?Quote:
Originally Posted by semaj
Check this site:Quote:
Originally Posted by Yodafone
http://forums.se-nse.net/index.php?showtopic=16148
my phone is CID 52. yours is 49... I think xs++3.0 can convert it to 52... just check the site and you'll a lot! you can change / add / or delete files easily with xs++... just like FAR but as i said... its much safer!
There's no CID52 Firmwares for K510.
I'm asking, using the FSX function in XS++, would it require bruteforcing?
And also, after flashing, would customising the file system (to stop the Config error) also require a bruteforce?
You can download new XS++3.1... your phone is supported... according to xs++ creators the wayin method is already obsolete (bruteforce), no need for wayin methods... try it its safe! just start FSX and press shutdown FSX after you are done thats it... no more complications.... about customising FS same! XS++ has generic custom packs already included...Quote:
Originally Posted by Yodafone
you can also download the help file of xs++... i think it is about 1.5MB in size...
Would I need to customize the file system if I modify files with FSX and not debrand?
Hi. I have a k800 with the R1JC002 firmware and red_52 rom. Do I have to flash only any firmware R1JC002 or can i use others like R1KGC001 for example??
Thank you!
You have to use matching FS and MAIN files. That's it.
No need to customize...Quote:
Originally Posted by Yodafone
So all I do is Connect with XS++, upload files via FSX, then click disconnect?
hi!, justme.
if I loose GDFS then what is the procedure to bypass config error, contact service centre. remember customization failed after flashing.
Don't really understand your question. Check your inbox.
correct... but remember use xs++3.1... it has a different UI than xs++2.x... first you connect phone... then press "start FSX"... upload files to the destination folders... after done, press "shutdown FSX"... then disconnect... very easy...Quote:
Originally Posted by Yodafone
Thank you.
I have a few more questions:
How long does a FSX take?
Does it automaticly overwrite files or do I have to delete the original file first then upload?
If it goes wrong, can SEUS repair it or do I need a FS file?
Thanks again.
Usinf the FSX procedure means that XS++ overwrite the files existing on your phone file system. If you do not like what you upload in your phone or if it doesn't work properly you cand upload the original content again with XS++ FSX mode.Quote:
Originally Posted by Yodafone
And yes, you can also use SEUS to reflash an existing file system.
OK I did it! (Custom Splash, startup and shutdown sounds)
But where do I find the other things like the battery/signal icons and the hourglass icon when the phone is busy.