Dead k800

Hi, I have a K800i cid 52 red on 3 which I have tried to unlock using setool2 lite 1.11. I firstly backed up the gdfs then flashed 'K800_R8BA024_MAIN_GENERIC_WI_RED52.mbn' onto it with a newly created 'quick_access_K800_R8BA024.vkp'. This all seemd to work fine and no errors were reported in the software. Prob is I now have a dead phone, no white screen or blinking ir led. I have tried to restore the gdfs to no avail. It gets as far as executing CS Loader and dies with a wrong response. the phone originally had cid49 R1ED001 firmware. the Cid was changed some time ago to 52 using wotan server, which offered to update when the phone was plugged into it. Does anyone have any thoughts as to whats gone wrong or how this can be reset/restored ?

Cheers Mike

Post Your XS++ Log Here.

Hi, Thanks for your reply. I now realise this was my fault. I tried to flash the phone just using the charger without the battery in. The phone obviously needs that bit more power to blow the eprom. it works fine now using xs but can you give me a link to instructions on how unlock using xs, as I don't seem to have that much luck with setool2!
Cheers Mike

You can`t unlock your phone by using xs++,only setool lite.

General Information about Patch-Unlocking (start here if you want to unlock)

Remove SIM-lock patch generator

Flash your phone and How to apply or remove patch using SETool 2 Lite

Nice day

Thanks again for your response. I have tried the patch as per instructions from your link, using a patch generated by the firmare currently on the phone(K800_R8BA024_MAIN_GENERIC_WI_RED52.mbn). This seems to go on correctly apart from one popup saying 'some patch values differs, continue ?' I continued at this point. After it has completed and I run the identify it shows errors and the phone will no longer switch on. Any thoughts as to why this should error ?

SE log below....

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170************ CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170************ CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:2019
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Trying to launch embedded bootloader...
INT LDR:DB2020_PRELOADER_FOR_SETOOL2
LDR:DB2020 LOADER FOR SETOOL2
Flash ID check:2019
Flash props sent ok
Going to execute VKP script....
Starting to process VKP patch script: C:\temp\Remove_SIM_lock_K800_R8BA024.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44740000
Blocks selected OK. Reading blocks: 1
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
VKP script executed OK
Elapsed:566 secs.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:49 PAF:1 IMEI:35170***********3 CERT:RED
FLASH CID:52 COLOR:RED
set_gdfs_props failed, exiting

Has anyone got thoughts on why this K800i should produce the 'some patch values differs, continue ?' error, when applying the remove lock patch with setool2, as mentioned in the previous text.

Cheers Mike.

You might be using a patch of another version...I suggest you flash to K810 R8BA024,and then unlock...

Nope, used 'K800_R8BA024_MAIN_GENERIC_WI_RED52.mbn' to flash and the remove sim lock script created from that firmware mbn and still get :

Going to execute VKP script....
Starting to process VKP patch script: C:\temp\Remove_SIM_lock_K800_R8BA024.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44740000
Blocks selected OK. Reading blocks: 1
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
VKP script executed OK

If I then go back to xs++ and flash R8BA024 to the phone, it works again but still locked to '3'...........

@huggim2 first debrand your phone, then unlock with Setool.

K800_R8BA024_FS_EUROPE_5_RED52
HB1-06_Generic_CDA102568_14_R4A_GENERIC_EUROPE_5
K800_R8BA024_MAIN_GENERIC_WI_RED52

Quote:

---

Originally Posted by huggim2

Nope, used 'K800_R8BA024_MAIN_GENERIC_WI_RED52.mbn' to flash and the remove sim lock script created from that firmware mbn and still get :

Going to execute VKP script....
Starting to process VKP patch script: C:\temp\Remove_SIM_lock_K800_R8BA024.vkp
VKP script loaded OK. Lines: 6
Patch structure created OK. Determining blocks to read...
New block #0000 added: $44740000
Blocks selected OK. Reading blocks: 1
Blocks readed to memory OK. Checking contents...
Blocks patched OK. Start writing...
Block 0 written
VKP script executed OK

If I then go back to xs++ and flash R8BA024 to the phone, it works again but still locked to '3'...........

---

But you MUST NOT flash the phone after patching!!!That's why it is locked then...