w810i unbranding problem

[mrwong]

Hi,

I'm not sure if I am posting in the right area. I just tried to flash/unbrand my phone, which i think i did correct. But for some reason when i go to menu it gives my a Dynamic Menu Error. Another thing is when i am in the menus one icon is missing. Last is when i try to text it wont let me get there the screen just turns white. Thanks to anyone that can help me, sorry for being a noobie.

o yea i have a cingular w810i that i still cant use mp3s as ring tones

[Khaba]

flash it again with a generic firmware

[mrwong]

I did the whole procedure over same thing... thanks for the advice though. I'm new to this and I dont know what I am doing wrong. I think I did flash it with the generic one. Any advice?

2.Install Far Manager from the Progs Directory
- now Copy the SEFP Folder from 0.10.0.44 from the "File" Directory to the
Far Manager to the "PlugIn" Folder of your Far Manager Install Diractory.
now overwrite the Folder with the SEFP Folder from 0.10.0.51.
- Now Copy the Files from the "\Files\Breakloader\SEFP" directory in the Plugins\SEFP
Directory an run the patch... Your Virus Software might say its a Trojan Horse.
But Ignored it and it worked fine!

NOW GET OUT YOUR SIM AND YOUR MEMRORY STICK!!

3. BreakIn Loader Flashing:
- Turn off your Phone
- run xs++ (from the Progs Folder) and press Start
- Connect the Phone while pressing "c"
- now press "Flash Mainfirmware" and open "w810_p3k_dcu.49R.ssw" from the Breakloader Directory
- Press Flash
- After 5-7 Sec. "finishing flash" should appear. Now You can press Stop and close XS++.
- Deconnect the Phone

PUT YOUR BATTERIE OUT OF YOUR PHONE FOR 5 SECS...

4.Modding

- Start the Far Manager
- Press F11 and choose "sefp 0.10.0.51"
- In the next Winow Chosse the following:
- Device: DCU -60
- Speed 921600
- Flow: As it is
- Boot Scripts: w300_w810_z550_
- connect the Phone while pressing "c"
- Now the left Window: Its the filestructure of your Phone. Press FS
...Files are Loaded...
- now go to /tpa/preset/system/desktop/flash
-on the right WIndow choose The Theme Folder of my Package.
- Now you can copy the wanted swf files from right to left by drag and drop...
IMPORTANT:
- If you are ready, press ".." at the top of the left window until a red window appears.
- Press "YES"
- Now close Far by pressing F10
- deconnect the Phone

PUT YOUR BATTERIE OUT OF YOUR PHONE FOR 5 SECS...

5. Finalize

- Open xs++ again
- Choose Flash Mainfirmware and Choose the file in the "Main Firmware" Folder which is W810_R4EA031_MAIN_GENERIC_HN_RED49.mbn
- Now Flash...
...takes about 2 Minutes...
- Deconnect the Phone an put in the Sims again. You are done.

[Khaba]

I think I know, your phone is branded cingular and you flashed a generic main, the problem might be occuring cuz you have cingular FS on the phone. if you want to flash it you need to use Cingular FS, Cingular MAIN and Cingular customs, or Generic MAIN and the according FS and customs to your area. I guess you want to unbrand it.

[mrwong]

kkk... thanks a lot for the help it works fine now!! this is a really noob question but what is fs and where do i go about inputting those files.
W810_R4ED001_FS_CINGULAR_RED49 or
W810_R4ED001_FS_AMERICA_1_RED49

THANKS A LOT for the help and putting up with my lack of knowing these things.

[Khaba]

Follow this tutorial: http://forum.gsmhosting.com/vbb/show...9&postcount=17 from the debarnding part, REPLACE the MEDITERR MAIN, FS and customization files and you should have an unbranded W810i. Read before doing it !!!!

[15jokasta]

Follow this tutorial: http://forum.gsmhosting.com/vbb/show...9&postcount=17 from the debarnding part, REPLACE the MEDITERR MAIN, FS and customization files and you should have an unbranded W810i. Read before doing it !!!!

[gsm420]

use setool

Here are 2 simple steps u need to follow:-

1. Unlock
2. Write Restoration File

Phone will be unlocked now!

Note:- if u do not write restoration file phone will end up dead