Results 1 to 1 of 1
  1. #1
    Advanced user
    Join Date
    Aug 2008
    Device
    W890i
    Posts
    158
    Thanks
    3
    Thanked 36 Times in 22 Posts

    (TUTORIAL) Full Unlock DB2012/DB2020/PNX3250/DB3150

    HOW TO FULL UNLOCK DB2012/DB2020/PNX3250/DB3150

    This is the method to perform full unlock (not patch unlock) with setool box: full CSCA unlock in client-server mode.

    See this thread for the logs needed:
    (INFO) Platforms and Logs cost - Top Sony Forums

    See this thread to know how to unlock PDA's:
    PDA Unlock - Top Sony Forums

    Note:
    Supported only USB DCU-60 interface.

    Tip:
    - Connect powered on phone to PC using USB DCU-60 cable and install USB drivers when asked to.
    - It is recommended to do that before starting CSCA unlock process.



    1. Select phone type in the SEMC A2 (for DB3150) and Sony Ericsson (for other platforms) tab.

    2. Select USB as interface and use DCU-60 cable. That is REQUIRED. Press 'Identify', it will make security units backup.


    Code:
    Loaded 51 flash descriptors
    
    SERVER SUPPORT ENABLED.
    
    SERVER CREDITS LEFT/USED: 30/0
    
    CARD COUNTERS: FLASH 28, UNLOCK 37
    
    Elapsed: 2 secs.
    
    ChipID:C802,EMP protocol:0401
    
    PHONE IS RED RETAIL PRODUCT
    
    FLASH CID detected:52
    
    OTP LOCKED:1 CID:52 PAF:1 IMEI:35880101XXXXXX CERT:RED
    
     
    
    Model:V640i
    
    MAPP CXC article: R1DA038     prg12004926_VODAFONE_JI
    
    MAPP CXC version: R1DA038
    
    Language Package:VFE-LIVE-B
    
    CDA article: 1201-9062
    
    CDA version: R12A
    
    Default article: 1200-4912
    
    Default version: R1DA038
    
    PROVIDER: 293-40
    
    Network LOCKED
    
     
    
    SECURITY UNITS BACKUP CREATED.
    
    Elapsed: 9 secs.

    3. Go to Settings tab and select both 'USE SERVER FOR CSCA UNLOCK/FLASH' and 'DO FULL UNLOCK INSTEAD OF USERCODE RESET' options

    4. Fill your account details (username, password, server IP)

    5. Back to SEMC A2 tab (DB3150) or Sony Ericsson tab (other platforms), press 'Unlock/Repair' button

    Code:
    SERVER SUPPORT ENABLED.
    
    ChipID:C802,EMP protocol:0401
    
    PHONE IS RED RETAIL PRODUCT
    
    FLASH CID detected:52
    
    OTP LOCKED:1 CID:52 PAF:1 IMEI:35880101XXXXXX CERT:RED
    
    LDR:2007-11-16 18:10 CXC1250843_DB31XX_CS_LOADER_ACC_SDRAM_R2A048
    
    LDR CAPS:SYSTEM FLASH 
    
    LDR:2007-11-16 18:12 CXC1250780_DB31XX_CS_LOADER_APP_SDRAM_R2A048
    
    LDR CAPS:SYSTEM FLASH GDFS FILESYSTEM TA 
    
    Executing CSCA-based unlock.
    
    Asking for EROM signature...
    
    Waiting for calculation process...
    
    RESPONSE: "35880101XXXXXX ADDED TO QUEUE,CHECK BACK LATER" (1)
    
    SIGNATURE QUEUED FOR CALCULATION, CHECK BACK LATER
    
    signature calculation not done,err: 26
    
    Elapsed: 9 secs.

    6. Attach phone holding pressed "C" key. Signature should be added to unlock queue. Now wait some time, and repeat steps from 1 to 6 until you get:

    Code:
    Executing CSCA-based unlock.
    
    Asking for EROM signature...
    
    Waiting for calculation process...
    
    RESPONSE: "SUCCESS" (1038)
    
    Backup security data...
    
    Erasing locks...
    
    
    
    DISCONNECT PHONE, FULLY TURN IT ON AND ATTACH AGAIN.
    
    BE SURE THAT YOU SET PHONE IN "PHONE MODE"
    
    IF ASKED, INSTALL PHONE DRIVERS
    
     
    
    SEARCHING FOR PHONE, "STOP" TO ABORT

    7. Disconnect phone, turn it fully on in "phone mode", connect powered on phone again to DCU-60. You should get:

    Code:
    PHONE FOUND AT COM64
    
    PHONE READY TO PROCEED.
    
    Connecting to server
    
    We got a step1 response
    
    seed is:00D2C3EC
    
    We got a step3 response
    
    signoff response ok
    
    Phone succefully unlocked. USERCODE RESET TO "0000"
    
    Elapsed: 78 secs.

    8. Done.

    Possible errors you may encounter

    Code:
    RESPONSE: "QUEUE FULL, CHECK BACK LATER" (15)
    
    Error "QUEUE FULL, CHECK BACK LATER" during signature calculation
    
    signature calculation not done,err: 144

    Queue is full, your signature is not added to queue, you need to try again (and again...) until you succeed.


    Code:
    RESPONSE: "35735401822168 ALREADY IN QUEUE" (30)
    
    MSG: "35735401822168"
    
    MSG: "35619601379365"
    
    signature calculation not done,err: 26

    Signature calculation is not done yet (in this case two phones are in queue for calculation). Wait some time, try again (go to step 8).


    Code:
    Asking for EROM signature...
    
    CAN'T CONNECT TO SERVER.
    
    signature calculation not done,err: 144
    
    Elapsed:30 secs.

    Server is offline, or internet communication problem. Check and try again.


    Code:
    Waiting for calculation process...
    
    UNKNOWN RESPONSE (24)
    
    signature calculation not done,err: 144

    Communication problem, check internet/firewall/antivirus settings, try again.


    Code:
    Waiting for calculation process...
    
    RESPONSE: "SUCCESS" (1038)
    
    loader startup: executed
    
    loader GDFS startup: executed
    
    loader unlock: executed
    
    Backup security data...
    
    Erasing locks...
    
     
    
    DISCONNECT PHONE, FULLY TURN IT ON AND ATTACH AGAIN.
    
    BE SURE THAT YOU SET PHONE IN "PHONE MODE"
    
    IF ASKED, INSTALL PHONE DRIVERS
    
     
    
    SEARCHING FOR PHONE, "STOP" TO ABORT
    
    PHONE FOUND AT COM4
    
    phone ready to proceed.
    
    Connecting to server
    
    No server found.
    
    Fail
    
    Elapsed:89 secs.

    Communication problem. Do not worry, simple repeat procedure, no extra logs will be charged.


    Code:
    Executing CSCA-based unlock.
    
    Asking for EROM signature...
    
    Waiting for calculation process...
    
    RESPONSE: "IMEI WAS ADDED BY ANOTHER USER" (0)
    
    Error "IMEI WAS ADDED BY ANOTHER USER" during signature calculation
    
    signature calculation not done,err: 144
    
    Elapsed:17 secs.

    Calculation request already received, either from another user or from you using different credits account.


    This is from the Official SETool box support.

    I hope it helps you out.

  2. The Following 3 Users Say Thank You to Willin08 For This Useful Post:


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •